Your location:Home   Products    Thermostatic Shaking Gas/Water Bath    SHZ-82A Thermostatic Shaking Water Bath
0
Shopping Cart
Delete all items
Proceed to send inquiry
*
*
*
SHZ-82A Thermostatic Shaking Water Bath
SHZ-82A Thermostatic Shaking Water Bath is manufactured by imported corrosion-resistant plate with advanced technical. Each index of performance can meet national standard requirements.
//www.jsjinyi.com/uploadfiles/128.1.164.122/webid258/source_water/202302/167686173377.jpg
Product Detail

Brief introduction


SHZ-82A Thermostatic Shaking Water Bath is manufactured by imported corrosion-resistant plate with advanced technical. Each index of performance can meet national standard requirements. SHZ-82A Thermostatic Shaking Water Bath is in possession of many merits, such as high precision of controlling temperature, steady oscillation, reliable quality, long service life and so on. SHZ-82A Thermostatic Shaking Water Bath is adopted advanced stainless spring multipurpose ones, used conveniently and extensively in culture of microorganism and also scientific research and experiments of food, life-form, medicine, agriculture, and environment protection.


Technical index


1. Power source: 220V 50Hz

2. Range of temperature controlled: RT-100℃ (precision≤±1℃ LED)

3. Rotary speed: Start-280rpm

4. Timing: 0-120 minutes

5. Oscillation amplitude: 20mm

6. Net capacity of working room: ≥400×320×220mm

7. Working load: 12 Kg

8. Working method: Rotary


Operational instruction


Set temperature:

Use SET key to set temperature, then the lower digital tube will be flashing (upper tube shows actual temperature), using △ to increase, and ▽ to reduce. The shift key can be used for faster set. After setting the temperature needed, pres SET again to complete the setting.


Sensor error correction:

Correction could be made when confirm the meter displayed is not a correct measurement value. Press the SET button for 3 seconds to enter the inner menu, after you select a parameter SC, use △ or ▽ key to modify this parameter. Sensor error correction range is-50 degrees to the +50 (correction range for 99.9-degree-meter is-9.9degree to+9.9degree), then press SET button for 3 seconds to exit. Factory corrected values is 0. When use it, please be careful not to make the corrected value into uncorrected.


Start auto-tuning:

This product can adapt to most control systems. The auto-tuning should be started only when controlling is particularly bad.

Using the following two modes to start auto-tuning.


Method one: hold the SHIFT key for three seconds to enter the State of auto-tuning. At led light starts blinking, indicating start of state parameter for automatic tuning. Instrument control heating system will be fluctuating around the set point for 2 seconds. When At light goes off, auto-tuning ends, new PID parameters are locked in chips.


Method two: press the SET button for 3 seconds to enter the inner menu, choose At, and press △ or ▽ to change the OFF on lower part into ON, then press SET button for 3 seconds to exit the setting state while also starting the auto-tuning.


Precautions


1. If timing is needed, adjust the knob to relevant place. If no adjust it to "ON".

2. While taking out or put into vessel, the instrument should be turned off.

3. The instrument should be placed steadily. Don't use it inclinely.

4. In order to assure the safety of your body and property, the outlet should have safety grounding device. The outlet must be turned off after finishing working.

The products in our factory are assure to be maintained all the time. Please use them at your ease. (Cost of production will be paid extenuatory when using improperly or imparing artificially)

Related products
Related news
Inquiry Now
Name: *
Mobile:
E-mail: *
Message: *
Verification code: *
  
Related products
Other products
Hot products